Introduction To Turbo Boost Pressure MAP Sensor 89421-71020
The 89421-71020 is an OEM-standard 3-pin intake manifold turbo boost pressure sensor (MAP / Turbo Pressure Sensor). It is specifically engineered for Toyota D-4D direct-injection common-rail turbocharged diesel platforms.
This sensor is widely equipped on iconic off-road, commercial, and utility vehicles. It is compatible with for Toyota Hilux (KUN26 / KUN16 / N70), for Toyota Land Cruiser Prado (120 / 150 Series), for Toyota HiAce (KDH200 Series), and for Toyota Fortuner. It accurately detects charge-air boost pressure and manifold vacuum across a broad range from 10 kPa up to 260 kPa (up to 1.6 bar positive boost).
Manufactured under strict IATF 16949 quality guidelines, it is interchangeable with production code 079800-7470 and OE reference 89421-20190. The sensor features a high-sensitivity micro-machined silicon piezoresistive (MEMS) core.
It delivers a fast, precise linear analog voltage signal (0.5V to 4.5V DC) to the Engine Control Module (ECM). This allows the ECU to dynamically control common-rail fuel injection timing, exhaust gas recirculation (EGR) rates, and variable nozzle turbocharger (VNT) vane positioning.
This product offers global auto parts distributors, diesel repair specialists, and fleet service centers a reliable, high-durability replacement. It restores engine acceleration and eliminates limp-home modes.
対応車種および純正部品対応リスト
以下に、車両ごとの適用範囲の全一覧および互換性のある純正部品番号を、ご参照用に掲載します。.
| Vehicle Make | 車種 | モデル年 | Displacement |
|---|---|---|---|
| トヨタ | Hilux / Hilux Vigo | 2004–2016 | 3.0L / 2.5L |
| トヨタ | Land Cruiser Prado | 2002–2009 | 3.0L |
| トヨタ | Land Cruiser Prado | 2009–2015 | 3.0L |
| トヨタ | HiAce / Commuter / Quantum | 2004–2019 | 3.0L / 2.5L |
| トヨタ | Fortuner | 2005–2015 | 3.0L / 2.5L |
| トヨタ | RegiusAce | 2004–2016 | 3.0L / 2.5L |
| トヨタ | Dyna / ToyoAce | 2004–2016 | 3.0L / 2.5L |
| トヨタ | Land Cruiser 70 / 200 | 2007–2020 | 4.5L V8 |
| OEM Part Number | 89421-71020 / 89421-20190 / 89421-71010 / 89421-71030 / 079800-7470 / 079800-4410 | ||
Note: All vehicle brand names and model designations below are referenced strictly for technical fitment and compatibility verification.
卸売取引条件
最小発注数量（MOQ）
Our 89421-71020 turbo boost pressure map sensor, standard minimum MOQ is 10 pieces per model. We also accept mixed orders of different sensor models to meet your diverse sourcing needs.
納期
For all in-stock turbo boost pressure map sensor, we can arrange shipment within 3-7 business days. For large-volume wholesale orders, the production and delivery cycle is approximately 20 to 25 business days.
保証規定
89421-71020 turbo boost pressure map sensor, come with a 12-month OE-quality warranty. If any manufacturing defect occurs within the warranty period, send us a video and we’ll offer a free return or exchange.
パッケージ
通常、梱包には標準的なニュートラルホワイトの段ボール箱を使用しています。また、お客様のご要望に応じて、特注色の段ボール箱やブランドロゴ入りの外装箱も製作可能です。.
交通
当社は、DHL、FedEx、UPSをはじめとする主要な国際宅配便会社と提携しています。そのため、ほぼすべての国や地域を対象とした世界中への配送を手配することが可能です。.
お支払い
当サイトでは、銀行振込、PayPal、ウェスタンユニオンなど、さまざまな安全な支払い方法に対応しています。長期間ご利用いただいているお客様には、柔軟な支払い条件についてもご相談に応じます。.
OEMおよびプライベートブランドサービス
当社のブランドパッケージは、各地域の市場のニーズに合わせて、サイズ、原材料、包装工程などをカスタマイズすることが可能です。さらに、世界中の卸売業者、販売代理店、大口購入者、商社に対し、柔軟かつ信頼性の高い生産パートナーシップを提供しています。 つまり、レーザー彫刻によるロゴ、カスタマイズされた製品ラベル、密封プラスチック袋、カラーボックスの印刷など、ワンストップのプライベートブランドサービスを提供しています。.
Professional Installation Guidelines
- Safety First: Turn off the engine ignition switch and disconnect the vehicle’s negative battery terminal before servicing electrical components.
- Locate the Sensor: On for Toyota Hilux, Prado, and HiAce (1KD/2KD engines), locate the 89421-71020 sensor mounted on the engine bay bulkhead or an intake manifold mounting bracket.
- Inspect Vacuum / Gas Filter Line: Disconnect the vacuum hose attached to the sensor’s barb nipple. Inspect the rubber line and the in-line gas filter (Toyota 90917-11036) for oil contamination, cracking, or clogging. Clean or replace the filter and hose as necessary.
- Disconnect & Unbolt: Depress the locking tab on the 3-pin electrical harness connector and pull to disconnect. Remove the single mounting bolt securing the metal-sleeved bracket.
- 新しいセンサーの取り付け: Position the new 89421-71020 sensor and tighten the mounting bolt to factory torque (approx. 6.0 – 8.0 Nm). Reattach the vacuum line securely onto the barb nipple.
- Reconnect & Clear Codes: Connect the 3-pin wiring harness until the locking tab clicks. Reconnect the battery terminal, start the diesel engine, check for smooth idle and throttle response, and use an OBD-II diagnostic scanner to clear any stored historical fault codes.
ヘルプセンター
よくあるご質問
Q1: Why is the small in-line gas filter (OE 90917-11036) critical when replacing the 89421-71020 sensor on for Toyota Hilux or Prado?
For Toyota D-4D engines, a small plastic in-line disc filter (90917-11036) sits on the vacuum hose. It is located between the intake manifold and the 89421-71020 sensor to trap oil mist and soot. After 80,000–100,000 km, it may clog or crack. A clogged filter restricts pressure, causing false low boost, sluggishness, and lost turbo power. When replacing the sensor, inspect or replace the filter too.
Q2: Which OBD-II diagnostic trouble codes (DTCs) point to a failing or contaminated 89421-71020 sensor?
A faulty, disconnected, or clogged 89421-71020 sensor can trigger these DTCs for Toyota vehicles:
P0105/P0106: MAP/BARO circuit malfunction/range
P0107/P0108: MAP circuit low/high voltage
P0234: Overboost
P0237/P0238: Boost sensor “A” circuit low/high
P1251: Turbo stepper motor/boost correlation
Symptoms include total boost loss and limp mode (RPM capped, 4WD warning on). You may also notice heavy black smoke under acceleration and an illuminated Check Engine Light.
Q3: Are part numbers 89421-71020 and 079800-7470 completely identical?
A: 89421-71020 is a part number commonly referenced for Toyota applications, while 079800-7470 is an alternative cross-reference number often associated with DENSO and typically found on the sensor body. Both numbers refer to the same physical part, with identical 3-pin connector layout, mounting bracket dimensions, and 10–260 kPa calibration curve.Part numbers and brand names are used for identification and cross-reference purposes only.
Q4: How can a technician test the 89421-71020 sensor using a digital multimeter?
A: With ignition ON (engine OFF) and harness connected: Pin 3 (VC) ≈ stable +5.0V DC reference; Pin 1 (E2) ≈ 0.0V ground continuity; Pin 2 (PIM) ≈ 1.2–1.4V DC at sea-level atmospheric pressure (~101 kPa). Under a calibrated hand pump, the signal should rise smoothly and linearly to ~3.8–4.2V DC at 1.5 bar (21.7 psi) boost. Any dropout or erratic voltage indicates internal diaphragm failure.
